VAG KKL 409.1 Cable VCDS-Lite 1.2 Driver and Software Installation Guide
- Kkl 409.1 Usb Driver
- Kkl 409.1 Windows 10
- Kkl 409.1 Software
- Vagkkl 409.1 Driver Download
- Vag Kkl K409 Treiber Download
Assuming you've read and understand all of the above, you can download the 'Virtual COM Port' drivers here: Home Products VCDS. Download the latest drivers for your Viaken VAG KKL USB interface to keep your Computer up-to-date. Assuming you've read and understand all of the above, you can download the 'Virtual COM Port' drivers here: Home Products VCDS. How to Install VAG-COM 409.1 KKL Cable. This article will guide you how to correctly install VAG-COM 409.1 KKL USB cable on. Download here VAG-COM Driver. VAG KKL 409.1 Cable VCDS-Lite 1.2 Driver and Software Installation Guide. VAG KKL 409.1 OBD2 USB. Software and download the VCDS-Lite.
SAFETY WARNING: Never start and run your engine inside of a closed garage. Always make sure there is good ventilation to prevent carbon monoxide poisoning. Carbon monoxide fumes are produced by your engine’s exhaust gases.
Kkl 409.1 Usb Driver
Compatible Product: VAG KKL 409.1 OBD2 USB Diagnostic Interface Cable
1. Go to www.obdinnovations.com/diagnostic-software and download the VCDS-Lite Software and the Drivers (CDM v2.08.30 WHQL Certified Windows Drivers)
2. Now plug the VAG-COM 409.1 USB cable into your PC. Windows will automatically detect the interface and attempt to find the correct drivers.
Kkl 409.1 Windows 10
3. Extract and Open the “CDM 2.08.30 WHQL Certified for VAG 409.1” folder that you downloaded. Run the “CDM 2.08.30 WHQL Certified” installer to install the required Windows Drivers for the cable. (You may need to right click the installer and Run as Administrator).
4. After the driver installation is complete, we will need to setup the COM Port for the interface. Go to Control Panel > Device Manager and find the device under “Ports (COM & LPT). It should be called “USB Serial Port” and you will see the COM port number that was assigned to it. If the COM port number is 1, 2, 3 or 4, you will not need to configure the port. If it is not in the port range from 1-4, you will need to right click the “USB Serial Port” , then click “Properties”, then click the “Port Settings” tab, then click “Advanced”. Using the drop down menu, select a COM Port Number from 1-4. Click OK and OK to exit out.
5. Connect the VAG-COM 409.1 cable to your car’s OBDII diagnostic port and turn your key to the 2nd turn to turn on your ignition.
6. Run the VCDS-Lite-1.2-Installer that you downloaded to install the VCDS-Lite software.
7. Now you can start the VCDS-Lite 1.2 software from the Desktop shortcut icon. Click on Options. Under Select COM Port, choose the COM Port Number you selected prior in the Device Manager and click on Test. If the connection was successful, a box will pop up to let you know and you will be able to save the settings and begin using the software.
Copyright © 2014 CVO Electronics, Inc. All rights reserved. Commercial use and distribution of the contents of the website is prohibited without express written consent of the author.
Purchase the VAG KKL Cable here: http://www.obdinnovations.com/vag-com-kkl-obd2-usb-interface-cable-with-ftdi-ft232rl-chip/
VAG KKL 409.1 Cable VCDS-Lite 1.2 Driver and Software Installation Guide
SAFETY WARNING: Never start and run your engine inside of a closed garage. Always make sure there is good ventilation to prevent carbon monoxide poisoning. Carbon monoxide fumes are produced by your engine’s exhaust gases.
Compatible Product: VAG KKL 409.1 OBD2 USB Diagnostic Interface Cable
1. Go to www.obdinnovations.com/diagnostic-software and download the VCDS-Lite Software and the Drivers (CDM v2.08.30 WHQL Certified Windows Drivers)
2. Now plug the VAG-COM 409.1 USB cable into your PC. Windows will automatically detect the interface and attempt to find the correct drivers.
3. Extract and Open the “CDM 2.08.30 WHQL Certified for VAG 409.1” folder that you downloaded. Run the “CDM 2.08.30 WHQL Certified” installer to install the required Windows Drivers for the cable. (You may need to right click the installer and Run as Administrator).
Kkl 409.1 Software
4. After the driver installation is complete, we will need to setup the COM Port for the interface. Go to Control Panel > Device Manager and find the device under “Ports (COM & LPT). It should be called “USB Serial Port” and you will see the COM port number that was assigned to it. If the COM port number is 1, 2, 3 or 4, you will not need to configure the port. If it is not in the port range from 1-4, you will need to right click the “USB Serial Port” , then click “Properties”, then click the “Port Settings” tab, then click “Advanced”. Using the drop down menu, select a COM Port Number from 1-4. Click OK and OK to exit out.
5. Connect the VAG-COM 409.1 cable to your car’s OBDII diagnostic port and turn your key to the 2nd turn to turn on your ignition.
6. Run the VCDS-Lite-1.2-Installer that you downloaded to install the VCDS-Lite software.
7. Now you can start the VCDS-Lite 1.2 software from the Desktop shortcut icon. Click on Options. Under Select COM Port, choose the COM Port Number you selected prior in the Device Manager and click on Test. If the connection was successful, a box will pop up to let you know and you will be able to save the settings and begin using the software.
Vagkkl 409.1 Driver Download
Copyright © 2014 CVO Electronics, Inc. All rights reserved. Commercial use and distribution of the contents of the website is prohibited without express written consent of the author.
Vag Kkl K409 Treiber Download
Purchase the VAG KKL Cable here: http://www.obdinnovations.com/vag-com-kkl-obd2-usb-interface-cable-with-ftdi-ft232rl-chip/